Horizontal copper cabling
Cat6 and Cat6A drops to desks, phones, printers, point of sale, wall displays and work areas, in plenum or riser-rated cable as the building requires.
Business Technology ยท Cabling
Structured Cabling and Fiber Installation in Orange County
Cat6, Cat6A and fiber installed, certified and documented by Telxpress technicians for new builds, tenant improvements and office moves, with the phones, network and cameras that ride on it installed by the same team.
- Our own technicians, not subcontractors
- Every link tested, labeled and documented
- Coordinated with your GC and property manager
Telxpress installs structured cabling for offices, clinics, schools and warehouses across Orange County and Southern California: Cat6 and Cat6A copper, fiber backbones, racks and patch panels, all labeled, tested and documented. Our own technicians handle new builds, tenant improvements and office moves, and coordinate directly with your general contractor and property manager.
Structured cabling is a standards-based way of wiring a building for voice, data, Wi-Fi, cameras and AV: horizontal cables from each work area to a patch panel in a telecom room, a backbone between rooms or floors, and labels and records that let any technician find any connection.
Tenant improvement (TI) is the construction work that adapts a leased space to a tenant's needs. Low-voltage cabling is part of it, and it is far cheaper to run while walls and ceilings are open than after the finish work is done.
Compare your options
Cat6, Cat6A or fiber: which cable does your project need?
The cable in the walls outlasts every phone, switch and camera connected to it, so the choice deserves a few minutes. Most projects use a mix.
| Consideration | Cat6 | Cat6A | Fiber |
|---|---|---|---|
| Typical use | Desk, phone and printer drops in smaller offices | Desk drops, Wi-Fi access points, cameras, meeting rooms and anywhere speed or power matters | Backbone between telecom rooms, floors and buildings; long runs |
| Speed over a full run | Good for everyday office traffic | Higher speeds over the full horizontal distance | Highest capacity and the longest distances |
| Power over Ethernet | Yes, suitable for phones and most access points | Yes, with better heat handling for high-power devices | No; devices at the far end need local power or a copper link |
| Interference | Fine in most offices; keep clear of electrical runs | Better shielding options for noisy environments | Immune to electrical interference |
| Cost and installation | Lowest material cost, easiest to terminate | Thicker cable, more labor to terminate, moderate premium | Higher material and termination cost; specialist tools |
| Best fit | Budget-conscious fit-outs with standard desk needs | New builds and tenant improvements that should last through several equipment refreshes | Multi-floor buildings, campuses, warehouses and links to outbuildings |
Not sure what the building has today? Our networking team can survey the existing cabling and switches, and our connectivity advisors check what fiber and carrier services reach the property.
What we install
What does a Telxpress cabling project include?
Fiber backbone and risers
Fiber between telecom rooms, across floors and to other buildings, fusion-spliced or field-terminated, with enclosures and patch cords to match your switches.
Telecom rooms and racks
Rack and cabinet layout, patch panels, vertical and horizontal cable management, grounding, power distribution and labeling that a stranger could follow.
Wi-Fi, camera and AV drops
Ceiling drops for access points, exterior and interior camera locations, conference-room table and display feeds, and paging or intercom wiring.
Pathways and cleanup
Conduit, J-hooks, cable tray, fire-stopping at penetrations, and removal of abandoned cable from previous tenants where the lease or code requires it.
Testing, certification and documentation
Certified test results for every link, labels at both ends, and as-built drawings that make later moves, adds and troubleshooting fast.
New builds, TIs and moves
How do we run a new build, tenant improvement or office move?
Four steps, coordinated with your general contractor and property management so the low-voltage work never holds up the schedule.
-
Walkthrough and drawings
We walk the space with you, your general contractor or property manager, mark every drop on the floor plan, choose cable types and pathways, and agree on the telecom room, rack and power layout.
-
Rough-in with the GC
While walls and ceilings are open we pull copper and fiber along the agreed pathways, set boxes and conduit, and follow the building rules on hours, insurance, fire-stopping and riser access.
-
Terminate, test and label
After finish work we terminate jacks and patch panels, dress the rack, certify every link with a cable tester, and label both ends of every run to match the drawing.
-
Document and hand over
You receive as-built drawings, test reports and a labeled rack, then our team installs the switches, phones, Wi-Fi and cameras on the same schedule so the office opens working.
Working with general contractors and property managers
We are used to being one trade among many. We attend the low-voltage walkthrough, submit drawings and schedules in the format the GC uses, carry the insurance certificates buildings ask for, book riser and telecom room access through property management, and work after hours when a building or neighboring tenant requires it. On an office move we also coordinate the carrier circuits and phone number transfers so the new address is live before the trucks arrive.
Why do labeling, testing and documentation matter?
Cabling is the one part of your technology nobody sees once the ceiling tiles go back. If it is undocumented, every future change starts with someone tracing wires. If it is untested, the first sign of a bad termination is a phone that drops calls or a camera that goes dark.
Every link we install is certified with a cable tester and the results come to you with the as-built drawings. Labels at both ends of every run match the report and the patch panel. That record is what lets our phone, surveillance and audio visual technicians add or move a device in minutes, and it is what manufacturers require before they honor a cabling warranty.
- Certified test report for every copper and fiber link
- Labels on jacks, patch panels and cables that match the drawings
- As-built floor plans with drop numbers and pathways
- Rack elevation and port map for the telecom room
- Warranty paperwork from the cable and connector manufacturer
Client results
What clients say about moves and new offices
It has been two months since our phone system was installed. The system has performed very well and is meeting all our needs. This memo is to thank you for your excellent service and prompt responses to our needs. When our law firm started up, we had to move very quickly to get up and running and the phones are a critical part of our operation. Tele Express was able to adapt to our changing needs with timely and competitively priced proposals. Installation was done to meet our schedules and your team reacted very well to our many special requests. Our thanks goes out to you for your in-depth knowledge of business needs and your high quality products and services which has served our company well. We look forward to an on-going relationship with Tele Express as we grow our business and partner with you for our future needs.
Our company has been doing business with Tele Express for over 7 years and the level of service that they have provided over the years has been second to none! We recently moved into a new facility and implemented a new Digital Telephone/ACD system. After careful planning, Tele Express was able to put together a system that met or exceeded our unique set of requirements. They also assisted in coordinating the move of all our telecommunications services from our old location to the new one. Because of their expertise this entire process went off without a hitch. I would highly recommend Tele Express to anyone who is looking for a telecom solutions provider. These guys are a class act!
Cabling questions owners and contractors ask us
Should we run Cat6 or Cat6A in a new office?
For most offices we recommend Cat6A for the main runs and anywhere Wi-Fi access points, meeting-room gear or cameras will connect, because it supports higher speeds and more power over the full length of a run and will outlast several equipment refreshes. Cat6 remains a sound, lower-cost choice for standard desk drops in smaller spaces.
Can you work with our general contractor on a tenant improvement?
Yes, and we prefer to be brought in early. We attend the low-voltage walkthrough, mark drop locations on the drawings, rough in cable while walls are open, and return to terminate and test after the finish work. We follow the building's rules on hours, insurance and access, and coordinate with property management for riser and telecom room access.
Do you test and certify every cable you install?
Every copper and fiber link is tested with a certification tester after termination, and you receive the results with your as-built documentation. Testing catches a bad crimp or a kinked cable before your phones or cameras do, and it is what manufacturers require to honor their cabling warranties. Labels at both ends match the report.
Can you move our phones, network and cabling to a new office?
Yes. Office moves are one of the most common projects we run. We survey the new space, cable it before move day, coordinate internet and phone number transfers with the carriers, relocate or replace the rack equipment, and have the phones, Wi-Fi and cameras working when your team arrives on the first morning.
When does a building need fiber instead of copper?
Fiber is the right choice for backbone links between telecom rooms, between floors, and between buildings on a campus, where runs are longer than copper allows or where electrical interference is a concern. Desk, phone, camera and access point drops stay on copper because they need Power over Ethernet. Most projects combine both.
Planning a build-out or a move?
Book a free consultation and we will walk the space with you, or take the free AI readiness assessment to see how the building's infrastructure fits your AI and cloud plans.
Last reviewed: . Published by Telxpress, Irvine, CA.